- 1 What happens if you use too much flux when soldering?
- 2 What happens if you use too much solder?
- 3 Can you use too much solder on copper pipe?
- 4 How do you get rid of excess flux?
- 5 Can you use too much flux?
- 6 What happens to solder without flux?
- 7 What should you not do after soldering?
- 8 Can you overheat solder?
- 9 Can you solder over old solder?
- 10 Do you need flux to solder?
- 11 Why do plumbers use bread?
- 12 How do you fix a bad solder joint on copper?
- 13 What removes flux?
- 14 Should you clean off flux?
- 15 How do you use CJ’s flux remover?
- 16 People also ask:
If you are using normal solder wire, it contains all the flux you need. If you are soldering copper pipe for example, excess flux will simply probably not compromise the joint, but will simply drip away. Excessive flux is just that much more you have to clean off your work.
What happens if you use too much flux when soldering?
Don’t overheat the flux If you don’t heat the joint enough, the solder won’t flow into it. If you heat the joint too long, you’ll burn the flux (it’ll smoke and turn black) and make it difficult to get the solder to flow into the joint.
What happens if you use too much solder?
Too Much Solder It is entirely possible that this blob of solder wets neither the pin nor the pad and is not a reliable electrical connection. The best evidence of proper wetting (and good electrical contact) is a nice concave surface as on the joint on the far left.
Can you use too much solder on copper pipe?
Use the proper amount of solder Don’t feed too much solder into the joint. It’s tempting to melt a few inches of solder into a joint as extra insurance against leaking. But excess solder can puddle inside pipes, restricting water flow, and can form small balls that break loose and damage faucet valves.
How do you get rid of excess flux?
The most common way to clean flux residues from a repair area is to saturate a cotton or foam swab with isopropyl alcohol or another cleaning solvent, and rub it around the repair area.
Can you use too much flux?
One, using much more than needed will basically drown your joint making it hard to heat to the right temperature, two, flux needs to be removed before a part is returned to service so every bit used that is more than needed makes for more clean up.
What happens to solder without flux?
Solid core solder has no rosin and requires the use of flux. Trying to use a solid core solder without flux will result in a practically useless joint. The solder will not cling to the surfaces and the oxides will break away causing the joint to fail.
What should you not do after soldering?
After soldering, immediately coat the tip in fresh solder to prevent oxidation. Avoid using sandpaper or anything that is too aggressive tools to remove oxidation. This can damage the iron plating that protects the copper underneath, shortening the life of the soldering iron.
Can you overheat solder?
Overheated solder joints can result from the soldering iron temperature being set too high, or result from solder failing to flow, possibly due to the surface of the pad or lead already having a layer of oxide, preventing sufficient heat transfer and therefore leaving you heating the joint for too long.
Can you solder over old solder?
It can not be done by just adding more solder. … Just heat the joint up with your torch, once the solder starts to melt use Channel locks to pull the fittings apart. Once the joint is apart, wipe as much old solder off as you can with a rag. Clean, Flux, solder.
Do you need flux to solder?
Yes, you can solder without flux. While it is helpful in the process of soldering as the flux helps break down the oxides on the metal, it is not needed. Also, most solder nowadays come with a rosin core which does the job of flux helping breaking down oxides.
Why do plumbers use bread?
“Use the bread to stop the leaks,” says Larry. … According to Larry, the plumber, when you need to solder a copper pipe that has a leak, first stuff it with a tightly rolled pie of fresh white bread! Fresh bread is the key, he insists. The bread will stop the leak long enough to get the soldering done.
How do you fix a bad solder joint on copper?
Just heat the joint up with your torch, once the solder starts to melt use Channel locks to pull the fittings apart. Once the joint is apart, wipe as much old solder off as you can with a rag. Now you can start over. Clean, Flux, solder.
What removes flux?
Isopropyl alcohol is the most common solvent used for removing flux, but Techspray offers flux removers that can do the job more effectively and efficiently. One common way to clean flux is the wet a swab with isopropyl alcohol and wipe around the solder joint.
Should you clean off flux?
Yes, flux should be cleaned off of a printed circuit board (PCB) after soldering is completed. … If the flux residue chars and forms spots on the solder joints, it may look like a true defect like a solder joint void or “blow hole”.
How do you use CJ’s flux remover?
Directions: Shake before using. Apply CJ’s directly to finished piece immediately after soldering. Scrub entire piece (glass, lead, solder joints) with soft brush and warm water, then rinse clean. If using a patina, apply now and rinse again.